Eaton DR125-680-R 2.7 A Saturation Shielded Inductor 68 uH
Eaton DR125-680-R 2.7 A Saturation Shielded Inductor 68 uH

Eaton DR125-680-R 2.7 A Saturation Shielded Inductor 68 uH

Share
Eaton DR125-680-R: Shielded Drum Core Power Inductor, 68 uH, 2.22 A, DCR 101 mOhm.
    • Product Details
    • Download

    Eaton DR125-680-R 2.7 A Saturation Shielded Inductor 68 uH

    DR125-680-R at a glance: shielded drum core inductor, 68 uH, 2.22 A Irms, 2.7 A Isat, DCR 101 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR125-680-R
    Rated inductance68 uH ±20%
    Open circuit inductance (OCL)67.9 uH
    Irms (40 °C rise)2.22 A
    Isat2.7 A
    DCR typical @ 20 °C101 mOhm
    Volt-microsecond rating38.6 V-us
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    Copper loss grows with the square of the current, so 101 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    What This Family Is For

    DR125 is the 6.0 mm member of the 12.5 mm family, with current up to 45 A peak. The larger body spreads the winding over more copper, which is where the current headroom comes from.

    • Typical applications: Desktop and servers, DC-DC converters, LCD panels, portable and handheld devices, noise filtering and filter chokes.
    • Peak current and RMS current are different limits on this series; the ripple current adds heating without adding output, so design to Irms for temperature and Isat for headroom.
    • Data sheet 4315.

    Putting It to Work

    Choose 68 uH when the ripple target is in the middle of the design window: the DCR stays at 101 mOhm and the saturation limit at 2.7 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products