Eaton DR125-6R8-R 6.8 uH Shielded Drum Core Inductor
Eaton DR125-6R8-R 6.8 uH Shielded Drum Core Inductor

Eaton DR125-6R8-R 6.8 uH Shielded Drum Core Inductor

Share
Eaton DR125-6R8-R: Shielded Drum Core Power Inductor, 6.8 uH, 6.64 A, DCR 12.3 mOhm.
    • Product Details
    • Download

    Eaton DR125-6R8-R 6.8 uH Shielded Drum Core Inductor

    DR125-6R8-R at a glance: shielded drum core inductor, 6.8 uH, 6.64 A Irms, 8.68 A Isat, DCR 12.3 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR125-6R8-R
    Rated inductance6.8 uH ±20%
    Open circuit inductance (OCL)6.59 uH
    Irms (40 °C rise)6.64 A
    Isat8.68 A
    DCR typical @ 20 °C12.3 mOhm
    Volt-microsecond rating12 V-us
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    Copper loss grows with the square of the current, so 12.3 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Positioning in the Range

    DR125 is the 6.0 mm member of the 12.5 mm family, with current up to 45 A peak. The larger body spreads the winding over more copper, which is where the current headroom comes from.

    • Typical applications: Desktop and servers, DC-DC converters, LCD panels, portable and handheld devices, noise filtering and filter chokes.
    • Peak current and RMS current are different limits on this series; the ripple current adds heating without adding output, so design to Irms for temperature and Isat for headroom.
    • Data sheet 4315.

    Design Notes

    At 6.8 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 12.3 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message