Eaton DR125-R47-R 0.47 uH Shielded Power Inductor, 17.6 A
Eaton DR125-R47-R 0.47 uH Shielded Power Inductor, 17.6 A

Eaton DR125-R47-R 0.47 uH Shielded Power Inductor, 17.6 A

Share
Eaton DR125-R47-R: Shielded Drum Core Power Inductor, 0.47 uH, 17.6 A, DCR 1.8 mOhm.
    • Product Details
    • Download

    Eaton DR125-R47-R 0.47 uH Shielded Power Inductor, 17.6 A

    DR125-R47-R at a glance: shielded drum core inductor, 0.47 uH, 17.6 A Irms, 33 A Isat, DCR 1.8 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR125-R47-R
    Rated inductance0.47 uH ±20%
    Open circuit inductance (OCL)0.46 uH
    Irms (40 °C rise)17.6 A
    Isat33 A
    DCR typical @ 20 °C1.8 mOhm
    Volt-microsecond rating3.17 V-us
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    At 1.8 mOhm this is a part where the winding, not the core, decides the temperature rise. The data sheet quotes the typical and the maximum separately for a reason: build your budget on the maximum.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Series Positioning

    DR125 is the 6.0 mm member of the 12.5 mm family, with current up to 45 A peak. The larger body spreads the winding over more copper, which is where the current headroom comes from.

    • Typical applications: Desktop and servers, DC-DC converters, LCD panels, portable and handheld devices, noise filtering and filter chokes.
    • Peak current and RMS current are different limits on this series; the ripple current adds heating without adding output, so design to Irms for temperature and Isat for headroom.
    • Data sheet 4315.

    Putting It to Work

    0.47 uH sits at the low end of the range, and the trade at that point is explicit: 1.8 mOhm of DCR against 33 A of saturation headroom.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products