Eaton DR127-2R2-R Shielded Drum Core, 2.2 uH uH 4.02 mOhm
Eaton DR127-2R2-R Shielded Drum Core, 2.2 uH uH 4.02 mOhm

Eaton DR127-2R2-R Shielded Drum Core, 2.2 uH uH 4.02 mOhm

Share
Eaton DR127-2R2-R: Shielded Drum Core Power Inductor, 2.2 uH, 12.5 A, DCR 4.02 mOhm.
    • Product Details
    • Download

    Eaton DR127-2R2-R Shielded Drum Core, 2.2 uH uH 4.02 mOhm

    DR127-2R2-R at a glance: shielded drum core inductor, 2.2 uH, 12.5 A Irms, 25.5 A Isat, DCR 4.02 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR127-2R2-R
    Rated inductance2.2 uH ±20%
    Open circuit inductance (OCL)2.03 uH
    Irms (40 °C rise)12.5 A
    Isat25.5 A
    DCR typical @ 20 °C4.02 mOhm
    Volt-microsecond rating7.7 V-us
    Package12.5 x 12.5 mm footprint, 8.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    Copper loss grows with the square of the current, so 4.02 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Where This Series Fits

    DR127 is the 8.0 mm tall version of the 12.5 mm DR family and the one that carries the highest current in the range, up to 56 A peak. Same pad as DR125, more height, more copper, more current.

    • Typical applications: High current DC-DC converters, servers and desktop power, graphics cards, battery powered systems, filter chokes.
    • At 8 mm the part is tall enough to matter for mechanical clearance and for airflow around neighbouring components - check both before layout.
    • Data sheet 4315.

    Putting It to Work

    2.2 uH is in the middle of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products