Eaton DR127-471-R 470 uH Shielded Drum Core Inductor
Eaton DR127-471-R 470 uH Shielded Drum Core Inductor

Eaton DR127-471-R 470 uH Shielded Drum Core Inductor

Share
Eaton DR127-471-R: Shielded Drum Core Power Inductor, 470 uH, 0.85 A, DCR 861 mOhm.
    • Product Details
    • Download

    Eaton DR127-471-R 470 uH Shielded Drum Core Inductor

    DR127-471-R at a glance: shielded drum core inductor, 470 uH, 0.85 A Irms, 1.68 A Isat, DCR 861 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR127-471-R
    Rated inductance470 uH ±20%
    Open circuit inductance (OCL)467 uH
    Irms (40 °C rise)0.85 A
    Isat1.68 A
    DCR typical @ 20 °C861 mOhm
    Volt-microsecond rating117 V-us
    Package12.5 x 12.5 mm footprint, 8.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    DCR 861 mOhm is the conduction loss: at the rated current it dissipates about 0.62 W, and that heat has to leave through the terminals and the board.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 30% rolloff at +20 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    What This Family Is For

    DR127 is the 8.0 mm tall version of the 12.5 mm DR family and the one that carries the highest current in the range, up to 56 A peak. Same pad as DR125, more height, more copper, more current.

    • Typical applications: High current DC-DC converters, servers and desktop power, graphics cards, battery powered systems, filter chokes.
    • At 8 mm the part is tall enough to matter for mechanical clearance and for airflow around neighbouring components - check both before layout.
    • Data sheet 4315.

    Sizing It Into a Design

    At 470 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 861 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products