Eaton DR127-4R7-R - 4.7 uH 8.25 A Shielded Inductor
Eaton DR127-4R7-R - 4.7 uH 8.25 A Shielded Inductor

Eaton DR127-4R7-R - 4.7 uH 8.25 A Shielded Inductor

Share
Eaton DR127-4R7-R: Shielded Drum Core Power Inductor, 4.7 uH, 8.25 A, DCR 9.17 mOhm.
    • Product Details
    • Download

    Eaton DR127-4R7-R - 4.7 uH 8.25 A Shielded Inductor

    DR127-4R7-R at a glance: shielded drum core inductor, 4.7 uH, 8.25 A Irms, 16.5 A Isat, DCR 9.17 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR127-4R7-R
    Rated inductance4.7 uH ±20%
    Open circuit inductance (OCL)4.84 uH
    Irms (40 °C rise)8.25 A
    Isat16.5 A
    DCR typical @ 20 °C9.17 mOhm
    Volt-microsecond rating11.9 V-us
    Package12.5 x 12.5 mm footprint, 8.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    Copper loss grows with the square of the current, so 9.17 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 30% rolloff at +20 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    What This Family Is For

    DR127 is the 8.0 mm tall version of the 12.5 mm DR family and the one that carries the highest current in the range, up to 56 A peak. Same pad as DR125, more height, more copper, more current.

    • Typical applications: High current DC-DC converters, servers and desktop power, graphics cards, battery powered systems, filter chokes.
    • At 8 mm the part is tall enough to matter for mechanical clearance and for airflow around neighbouring components - check both before layout.
    • Data sheet 4315.

    Putting It to Work

    4.7 uH sits in the middle of the range, and the trade at that point is explicit: 9.17 mOhm of DCR against 16.5 A of saturation headroom.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products