Eaton DR127-821-R 820 uH Shielded Power Inductor, 0.65 A
Eaton DR127-821-R 820 uH Shielded Power Inductor, 0.65 A

Eaton DR127-821-R 820 uH Shielded Power Inductor, 0.65 A

Share
Eaton DR127-821-R: Shielded Drum Core Power Inductor, 820 uH, 0.65 A, DCR 1.47 ohm.
    • Product Details
    • Download

    Eaton DR127-821-R 820 uH Shielded Power Inductor, 0.65 A

    DR127-821-R at a glance: shielded drum core inductor, 820 uH, 0.65 A Irms, 1.27 A Isat, DCR 1470 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR127-821-R
    Rated inductance820 uH ±20%
    Open circuit inductance (OCL)818 uH
    Irms (40 °C rise)0.65 A
    Isat1.27 A
    DCR typical @ 20 °C1470 mOhm
    Volt-microsecond rating155 V-us
    Package12.5 x 12.5 mm footprint, 8.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    DCR 1470 mOhm is the conduction loss: at the rated current it dissipates about 0.62 W, and that heat has to leave through the terminals and the board.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    DR127 is the 8.0 mm tall version of the 12.5 mm DR family and the one that carries the highest current in the range, up to 56 A peak. Same pad as DR125, more height, more copper, more current.

    • Typical applications: High current DC-DC converters, servers and desktop power, graphics cards, battery powered systems, filter chokes.
    • At 8 mm the part is tall enough to matter for mechanical clearance and for airflow around neighbouring components - check both before layout.
    • Data sheet 4315.

    Sizing and Layout Notes

    820 uH is at the high end of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message