Eaton DR73-102-R 1000 uH Shielded Power Inductor, 0.26 A
Eaton DR73-102-R 1000 uH Shielded Power Inductor, 0.26 A

Eaton DR73-102-R 1000 uH Shielded Power Inductor, 0.26 A

Share
Eaton DR73-102-R: Shielded Drum Core Power Inductor, 1000 uH, 0.26 A, DCR 4.34 ohm.
    • Product Details
    • Download

    Eaton DR73-102-R 1000 uH Shielded Power Inductor, 0.26 A

    DR73-102-R at a glance: shielded drum core inductor, 1000 uH, 0.26 A Irms, 0.25 A Isat, DCR 4340 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR73-102-R
    Rated inductance1000 uH ±20%
    Open circuit inductance (OCL)995 uH
    Irms (40 °C rise)0.26 A
    Isat0.25 A
    DCR typical @ 20 °C4340 mOhm
    Volt-microsecond rating113 V-us
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    The DC resistance sets the efficiency floor. 4340 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    What This Family Is For

    DR73 is the smallest of the four DR sizes: a 7.6 x 7.6 mm shielded drum core in a 3.55 mm max height, covering 0.33 uH to 1000 uH across the family. Small package, real current - this is the size that fits a dense point-of-load rail.

    • Typical applications: Desktop and servers, DVD and media players, portable and handheld devices, LCD panels, DC-DC converters, noise filtering.
    • The 7.6 mm body has less copper area than the 12.5 mm parts, so the DCR is higher for the same inductance - budget the loss accordingly.
    • Data sheet 4315.

    Putting It to Work

    1000 uH sits at the high end of the range, and the trade at that point is explicit: 4340 mOhm of DCR against 0.25 A of saturation headroom.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message