Eaton DR73-150-R 15 uH Shielded Drum Core Inductor
Eaton DR73-150-R 15 uH Shielded Drum Core Inductor

Eaton DR73-150-R 15 uH Shielded Drum Core Inductor

Share
Eaton DR73-150-R: Shielded Drum Core Power Inductor, 15 uH, 1.83 A, DCR 84.4 mOhm.
    • Product Details
    • Download

    Eaton DR73-150-R 15 uH Shielded Drum Core Inductor

    DR73-150-R at a glance: shielded drum core inductor, 15 uH, 1.83 A Irms, 2.05 A Isat, DCR 84.4 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR73-150-R
    Rated inductance15 uH ±20%
    Open circuit inductance (OCL)15 uH
    Irms (40 °C rise)1.83 A
    Isat2.05 A
    DCR typical @ 20 °C84.4 mOhm
    Volt-microsecond rating13.9 V-us
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    DCR 84.4 mOhm is the conduction loss: at the rated current it dissipates about 0.28 W, and that heat has to leave through the terminals and the board.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 30% rolloff at +20 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    What This Family Is For

    DR73 is the smallest of the four DR sizes: a 7.6 x 7.6 mm shielded drum core in a 3.55 mm max height, covering 0.33 uH to 1000 uH across the family. Small package, real current - this is the size that fits a dense point-of-load rail.

    • Typical applications: Desktop and servers, DVD and media players, portable and handheld devices, LCD panels, DC-DC converters, noise filtering.
    • The 7.6 mm body has less copper area than the 12.5 mm parts, so the DCR is higher for the same inductance - budget the loss accordingly.
    • Data sheet 4315.

    Putting It to Work

    At 15 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 84.4 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products