Eaton DR73-331-R 0.44 A Saturation Shielded Inductor 330 uH
Eaton DR73-331-R 0.44 A Saturation Shielded Inductor 330 uH

Eaton DR73-331-R 0.44 A Saturation Shielded Inductor 330 uH

Share
Eaton DR73-331-R: Shielded Drum Core Power Inductor, 330 uH, 0.42 A, DCR 1.59 ohm.
    • Product Details
    • Download

    Eaton DR73-331-R 0.44 A Saturation Shielded Inductor 330 uH

    DR73-331-R at a glance: shielded drum core inductor, 330 uH, 0.42 A Irms, 0.44 A Isat, DCR 1590 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR73-331-R
    Rated inductance330 uH ±20%
    Open circuit inductance (OCL)326 uH
    Irms (40 °C rise)0.42 A
    Isat0.44 A
    DCR typical @ 20 °C1590 mOhm
    Volt-microsecond rating64.5 V-us
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    The DC resistance sets the efficiency floor. 1590 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Positioning in the Range

    DR73 is the smallest of the four DR sizes: a 7.6 x 7.6 mm shielded drum core in a 3.55 mm max height, covering 0.33 uH to 1000 uH across the family. Small package, real current - this is the size that fits a dense point-of-load rail.

    • Typical applications: Desktop and servers, DVD and media players, portable and handheld devices, LCD panels, DC-DC converters, noise filtering.
    • The 7.6 mm body has less copper area than the 12.5 mm parts, so the DCR is higher for the same inductance - budget the loss accordingly.
    • Data sheet 4315.

    Sizing It Into a Design

    330 uH is in the middle of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products