Eaton DR73-3R3-R 3.3 uH Shielded Power Inductor, 3.31 A
Eaton DR73-3R3-R 3.3 uH Shielded Power Inductor, 3.31 A

Eaton DR73-3R3-R 3.3 uH Shielded Power Inductor, 3.31 A

Share
Eaton DR73-3R3-R: Shielded Drum Core Power Inductor, 3.3 uH, 3.31 A, DCR 25.9 mOhm.
    • Product Details
    • Download

    Eaton DR73-3R3-R 3.3 uH Shielded Power Inductor, 3.31 A

    DR73-3R3-R at a glance: shielded drum core inductor, 3.3 uH, 3.31 A Irms, 4.22 A Isat, DCR 25.9 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR73-3R3-R
    Rated inductance3.3 uH ±20%
    Open circuit inductance (OCL)3.54 uH
    Irms (40 °C rise)3.31 A
    Isat4.22 A
    DCR typical @ 20 °C25.9 mOhm
    Volt-microsecond rating6.73 V-us
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    DCR 25.9 mOhm is the conduction loss: at the rated current it dissipates about 0.28 W, and that heat has to leave through the terminals and the board.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Where This Series Fits

    DR73 is the smallest of the four DR sizes: a 7.6 x 7.6 mm shielded drum core in a 3.55 mm max height, covering 0.33 uH to 1000 uH across the family. Small package, real current - this is the size that fits a dense point-of-load rail.

    • Typical applications: Desktop and servers, DVD and media players, portable and handheld devices, LCD panels, DC-DC converters, noise filtering.
    • The 7.6 mm body has less copper area than the 12.5 mm parts, so the DCR is higher for the same inductance - budget the loss accordingly.
    • Data sheet 4315.

    Sizing and Layout Notes

    At 3.3 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 25.9 mOhm DCR - more turns, thinner wire, more resistance.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message