Eaton DR73-470-R 47 uH Shielded Drum Core Inductor
Eaton DR73-470-R 47 uH Shielded Drum Core Inductor

Eaton DR73-470-R 47 uH Shielded Drum Core Inductor

Share
Eaton DR73-470-R: Shielded Drum Core Power Inductor, 47 uH, 1.08 A, DCR 241 mOhm.
    • Product Details
    • Download

    Eaton DR73-470-R 47 uH Shielded Drum Core Inductor

    DR73-470-R at a glance: shielded drum core inductor, 47 uH, 1.08 A Irms, 1.14 A Isat, DCR 241 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR73-470-R
    Rated inductance47 uH ±20%
    Open circuit inductance (OCL)48.6 uH
    Irms (40 °C rise)1.08 A
    Isat1.14 A
    DCR typical @ 20 °C241 mOhm
    Volt-microsecond rating24.9 V-us
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    Copper loss grows with the square of the current, so 241 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    What This Family Is For

    DR73 is the smallest of the four DR sizes: a 7.6 x 7.6 mm shielded drum core in a 3.55 mm max height, covering 0.33 uH to 1000 uH across the family. Small package, real current - this is the size that fits a dense point-of-load rail.

    • Typical applications: Desktop and servers, DVD and media players, portable and handheld devices, LCD panels, DC-DC converters, noise filtering.
    • The 7.6 mm body has less copper area than the 12.5 mm parts, so the DCR is higher for the same inductance - budget the loss accordingly.
    • Data sheet 4315.

    Design Notes

    47 uH sits in the middle of the range, and the trade at that point is explicit: 241 mOhm of DCR against 1.14 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message