Eaton DR73-471-R - 470 uH 0.35 A Shielded Inductor
Eaton DR73-471-R - 470 uH 0.35 A Shielded Inductor

Eaton DR73-471-R - 470 uH 0.35 A Shielded Inductor

Share
Eaton DR73-471-R: Shielded Drum Core Power Inductor, 470 uH, 0.35 A, DCR 2.36 ohm.
    • Product Details
    • Download

    Eaton DR73-471-R - 470 uH 0.35 A Shielded Inductor

    DR73-471-R at a glance: shielded drum core inductor, 470 uH, 0.35 A Irms, 0.37 A Isat, DCR 2360 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR73-471-R
    Rated inductance470 uH ±20%
    Open circuit inductance (OCL)466 uH
    Irms (40 °C rise)0.35 A
    Isat0.37 A
    DCR typical @ 20 °C2360 mOhm
    Volt-microsecond rating77.2 V-us
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    DCR 2360 mOhm is the conduction loss: at the rated current it dissipates about 0.29 W, and that heat has to leave through the terminals and the board.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Series Positioning

    DR73 is the smallest of the four DR sizes: a 7.6 x 7.6 mm shielded drum core in a 3.55 mm max height, covering 0.33 uH to 1000 uH across the family. Small package, real current - this is the size that fits a dense point-of-load rail.

    • Typical applications: Desktop and servers, DVD and media players, portable and handheld devices, LCD panels, DC-DC converters, noise filtering.
    • The 7.6 mm body has less copper area than the 12.5 mm parts, so the DCR is higher for the same inductance - budget the loss accordingly.
    • Data sheet 4315.

    Sizing It Into a Design

    At 470 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 2360 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products