Eaton DR73-680-R 0.96 A Saturation Shielded Inductor 68 uH
Eaton DR73-680-R 0.96 A Saturation Shielded Inductor 68 uH

Eaton DR73-680-R 0.96 A Saturation Shielded Inductor 68 uH

Share
Eaton DR73-680-R: Shielded Drum Core Power Inductor, 68 uH, 0.89 A, DCR 358 mOhm.
    • Product Details
    • Download

    Eaton DR73-680-R 0.96 A Saturation Shielded Inductor 68 uH

    DR73-680-R at a glance: shielded drum core inductor, 68 uH, 0.89 A Irms, 0.96 A Isat, DCR 358 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR73-680-R
    Rated inductance68 uH ±20%
    Open circuit inductance (OCL)68.9 uH
    Irms (40 °C rise)0.89 A
    Isat0.96 A
    DCR typical @ 20 °C358 mOhm
    Volt-microsecond rating29.7 V-us
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    At 358 mOhm this is a part where the winding, not the core, decides the temperature rise. The data sheet quotes the typical and the maximum separately for a reason: build your budget on the maximum.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    What This Family Is For

    DR73 is the smallest of the four DR sizes: a 7.6 x 7.6 mm shielded drum core in a 3.55 mm max height, covering 0.33 uH to 1000 uH across the family. Small package, real current - this is the size that fits a dense point-of-load rail.

    • Typical applications: Desktop and servers, DVD and media players, portable and handheld devices, LCD panels, DC-DC converters, noise filtering.
    • The 7.6 mm body has less copper area than the 12.5 mm parts, so the DCR is higher for the same inductance - budget the loss accordingly.
    • Data sheet 4315.

    Putting It to Work

    68 uH sits in the middle of the range, and the trade at that point is explicit: 358 mOhm of DCR against 0.96 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message