Eaton DR73-8R2-R 2.66 A Saturation Shielded Inductor 8.2 uH
Eaton DR73-8R2-R 2.66 A Saturation Shielded Inductor 8.2 uH

Eaton DR73-8R2-R 2.66 A Saturation Shielded Inductor 8.2 uH

Share
Eaton DR73-8R2-R: Shielded Drum Core Power Inductor, 8.2 uH, 2.19 A, DCR 59.2 mOhm.
    • Product Details
    • Download

    Eaton DR73-8R2-R 2.66 A Saturation Shielded Inductor 8.2 uH

    DR73-8R2-R at a glance: shielded drum core inductor, 8.2 uH, 2.19 A Irms, 2.66 A Isat, DCR 59.2 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR73-8R2-R
    Rated inductance8.2 uH ±20%
    Open circuit inductance (OCL)8.93 uH
    Irms (40 °C rise)2.19 A
    Isat2.66 A
    DCR typical @ 20 °C59.2 mOhm
    Volt-microsecond rating10.7 V-us
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    Copper loss grows with the square of the current, so 59.2 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    What This Family Is For

    DR73 is the smallest of the four DR sizes: a 7.6 x 7.6 mm shielded drum core in a 3.55 mm max height, covering 0.33 uH to 1000 uH across the family. Small package, real current - this is the size that fits a dense point-of-load rail.

    • Typical applications: Desktop and servers, DVD and media players, portable and handheld devices, LCD panels, DC-DC converters, noise filtering.
    • The 7.6 mm body has less copper area than the 12.5 mm parts, so the DCR is higher for the same inductance - budget the loss accordingly.
    • Data sheet 4315.

    Design Notes

    At 8.2 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 59.2 mOhm DCR - more turns, thinner wire, more resistance.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products