Eaton DR73-R33-R 0.33 uH Shielded Power Inductor, 6.21 A
Eaton DR73-R33-R 0.33 uH Shielded Power Inductor, 6.21 A

Eaton DR73-R33-R 0.33 uH Shielded Power Inductor, 6.21 A

Share
Eaton DR73-R33-R: Shielded Drum Core Power Inductor, 0.33 uH, 6.21 A, DCR 7.3 mOhm.
    • Product Details
    • Download

    Eaton DR73-R33-R 0.33 uH Shielded Power Inductor, 6.21 A

    DR73-R33-R at a glance: shielded drum core inductor, 0.33 uH, 6.21 A Irms, 14.4 A Isat, DCR 7.3 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR73-R33-R
    Rated inductance0.33 uH ±20%
    Open circuit inductance (OCL)0.31 uH
    Irms (40 °C rise)6.21 A
    Isat14.4 A
    DCR typical @ 20 °C7.3 mOhm
    Volt-microsecond rating1.98 V-us
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    DCR 7.3 mOhm is the conduction loss: at the rated current it dissipates about 0.28 W, and that heat has to leave through the terminals and the board.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Positioning in the Range

    DR73 is the smallest of the four DR sizes: a 7.6 x 7.6 mm shielded drum core in a 3.55 mm max height, covering 0.33 uH to 1000 uH across the family. Small package, real current - this is the size that fits a dense point-of-load rail.

    • Typical applications: Desktop and servers, DVD and media players, portable and handheld devices, LCD panels, DC-DC converters, noise filtering.
    • The 7.6 mm body has less copper area than the 12.5 mm parts, so the DCR is higher for the same inductance - budget the loss accordingly.
    • Data sheet 4315.

    Sizing and Layout Notes

    0.33 uH sits at the low end of the range, and the trade at that point is explicit: 7.3 mOhm of DCR against 14.4 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message