Eaton DR74-1R5-R 1.5 uH Shielded Power Inductor, 4.94 A
Eaton DR74-1R5-R 1.5 uH Shielded Power Inductor, 4.94 A

Eaton DR74-1R5-R 1.5 uH Shielded Power Inductor, 4.94 A

Share
Eaton DR74-1R5-R: Shielded Drum Core Power Inductor, 1.5 uH, 4.94 A, DCR 11.8 mOhm.
    • Product Details
    • Download

    Eaton DR74-1R5-R 1.5 uH Shielded Power Inductor, 4.94 A

    DR74-1R5-R at a glance: shielded drum core inductor, 1.5 uH, 4.94 A Irms, 8.35 A Isat, DCR 11.8 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR74-1R5-R
    Rated inductance1.5 uH ±20%
    Open circuit inductance (OCL)1.42 uH
    Irms (40 °C rise)4.94 A
    Isat8.35 A
    DCR typical @ 20 °C11.8 mOhm
    Volt-microsecond rating3.76 V-us
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    At 11.8 mOhm this is a part where the winding, not the core, decides the temperature rise. The data sheet quotes the typical and the maximum separately for a reason: build your budget on the maximum.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Series Positioning

    DR74 uses the same 7.6 x 7.6 mm pad as DR73 but stands 4.35 mm tall instead of 3.55 mm. The extra height is what allows the higher current ratings in this size class without changing the land pattern.

    • Typical applications: Desktop and servers, DVD and media players, portable devices, LCD panels, DC-DC converters, buck and boost stages.
    • Because the footprint matches DR73, a current upgrade can be a straight swap - verify the clearance above the part before you commit to the taller body.
    • Data sheet 4315.

    Putting It to Work

    1.5 uH sits in the middle of the range, and the trade at that point is explicit: 11.8 mOhm of DCR against 8.35 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message