Eaton DR74-330-R 1.73 A Saturation Shielded Inductor 33 uH
Eaton DR74-330-R 1.73 A Saturation Shielded Inductor 33 uH

Eaton DR74-330-R 1.73 A Saturation Shielded Inductor 33 uH

Share
Eaton DR74-330-R: Shielded Drum Core Power Inductor, 33 uH, 1.41 A, DCR 143 mOhm.
    • Product Details
    • Download

    Eaton DR74-330-R 1.73 A Saturation Shielded Inductor 33 uH

    DR74-330-R at a glance: shielded drum core inductor, 33 uH, 1.41 A Irms, 1.73 A Isat, DCR 143 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR74-330-R
    Rated inductance33 uH ±20%
    Open circuit inductance (OCL)33 uH
    Irms (40 °C rise)1.41 A
    Isat1.73 A
    DCR typical @ 20 °C143 mOhm
    Volt-microsecond rating18.1 V-us
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    The DC resistance sets the efficiency floor. 143 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Positioning in the Range

    DR74 uses the same 7.6 x 7.6 mm pad as DR73 but stands 4.35 mm tall instead of 3.55 mm. The extra height is what allows the higher current ratings in this size class without changing the land pattern.

    • Typical applications: Desktop and servers, DVD and media players, portable devices, LCD panels, DC-DC converters, buck and boost stages.
    • Because the footprint matches DR73, a current upgrade can be a straight swap - verify the clearance above the part before you commit to the taller body.
    • Data sheet 4315.

    Design Notes

    33 uH sits in the middle of the range, and the trade at that point is explicit: 143 mOhm of DCR against 1.73 A of saturation headroom.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products