Eaton DR74-R33-R 0.33 uH Shielded Drum Core Inductor
Eaton DR74-R33-R 0.33 uH Shielded Drum Core Inductor

Eaton DR74-R33-R 0.33 uH Shielded Drum Core Inductor

Share
Eaton DR74-R33-R: Shielded Drum Core Power Inductor, 0.33 uH, 6.26 A, DCR 7.4 mOhm.
    • Product Details
    • Download

    Eaton DR74-R33-R 0.33 uH Shielded Drum Core Inductor

    DR74-R33-R at a glance: shielded drum core inductor, 0.33 uH, 6.26 A Irms, 18.4 A Isat, DCR 7.4 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR74-R33-R
    Rated inductance0.33 uH ±20%
    Open circuit inductance (OCL)0.29 uH
    Irms (40 °C rise)6.26 A
    Isat18.4 A
    DCR typical @ 20 °C7.4 mOhm
    Volt-microsecond rating1.71 V-us
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    Copper loss grows with the square of the current, so 7.4 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Where This Series Fits

    DR74 uses the same 7.6 x 7.6 mm pad as DR73 but stands 4.35 mm tall instead of 3.55 mm. The extra height is what allows the higher current ratings in this size class without changing the land pattern.

    • Typical applications: Desktop and servers, DVD and media players, portable devices, LCD panels, DC-DC converters, buck and boost stages.
    • Because the footprint matches DR73, a current upgrade can be a straight swap - verify the clearance above the part before you commit to the taller body.
    • Data sheet 4315.

    Putting It to Work

    At 0.33 uH this part is at the low end of the family. The winding that produces that inductance is also what sets the 7.4 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message