Eaton DRA125-101-R - 100 uH AEC-Q200 Power Inductor
Eaton DRA125-101-R - 100 uH AEC-Q200 Power Inductor

Eaton DRA125-101-R - 100 uH AEC-Q200 Power Inductor

Share
Eaton DRA125-101-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 100 uH, 1.75 A, DCR 178 mOhm.
    • Product Details
    • Download

    Eaton DRA125-101-R - 100 uH AEC-Q200 Power Inductor

    DRA125-101-R at a glance: shielded drum core inductor, 100 uH, 1.75 A Irms, 2.21 A Isat, DCR 178 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRA125-101-R
    Rated inductance100 uH ±20%
    Open circuit inductance (OCL)97.6 uH
    Irms (40 °C rise)1.75 A
    Isat1 (30% rolloff @ +25 °C)2.21 A
    Isat2 (40% rolloff @ +125 °C)1.77 A
    DCR typical @ 20 °C178 mOhm
    DCR maximum @ 20 °C214 mOhm
    K-factor (Bp-p = K x L x dI)11.8
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Automotive magnetics are specified differently: the temperature range is wider, the qualification is AEC-Q200, and the construction has to hold together under vibration that would shake a commercial part off its pads. That is what the DRA series is.

    Automotive thermal cycles are the hard part: the part may be rated to 165 °C, but every power cycle flexes the solder joint. The four-terminal variants exist precisely because two terminals are not always enough.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Where This Series Fits

    DRA125 is the 12.5 mm AEC-Q200 part at mid height - more current than DRA124, same footprint, so an upgrade does not force a board respin.

    • Typical applications: Automotive DC-DC converters, body control modules, LED lighting, ADAS, infotainment supplies.
    • Shielding matters in a module full of radios and sensors: the closed drum keeps the field in, but the layout still has to keep the hot loop small.
    • Data sheet 4319.

    Sizing and Layout Notes

    100 uH is in the middle of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    How does it differ from the commercial DR part of the same size?
    The electrical shape is similar, the qualification, the temperature range and often the terminal construction are not. Do not assume drop-in equivalence.

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message