Eaton DRA125-330-R Automotive Drum Core Inductor 33 uH
Eaton DRA125-330-R Automotive Drum Core Inductor 33 uH

Eaton DRA125-330-R Automotive Drum Core Inductor 33 uH

Share
Eaton DRA125-330-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 33 uH, 3.19 A, DCR 53 mOhm.
    • Product Details
    • Download

    Eaton DRA125-330-R Automotive Drum Core Inductor 33 uH

    DRA125-330-R at a glance: shielded drum core inductor, 33 uH, 3.19 A Irms, 3.86 A Isat, DCR 53 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRA125-330-R
    Rated inductance33 uH ±20%
    Open circuit inductance (OCL)31.5 uH
    Irms (40 °C rise)3.19 A
    Isat1 (30% rolloff @ +25 °C)3.86 A
    Isat2 (40% rolloff @ +125 °C)3.09 A
    DCR typical @ 20 °C53 mOhm
    DCR maximum @ 20 °C64 mOhm
    K-factor (Bp-p = K x L x dI)20.6
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    AEC-Q200 is the entry ticket, not the destination. This part is qualified to the automotive standard and rated to 165 °C ambient plus self-heating, in a shielded drum core built to survive shock and vibration rather than a laboratory bench.

    At 165 °C the copper resistivity is about 60% higher than at 20 °C, so the DCR in the table is optimistic at the hot corner - budget the loss accordingly.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Series Positioning

    DRA125 is the 12.5 mm AEC-Q200 part at mid height - more current than DRA124, same footprint, so an upgrade does not force a board respin.

    • Typical applications: Automotive DC-DC converters, body control modules, LED lighting, ADAS, infotainment supplies.
    • Shielding matters in a module full of radios and sensors: the closed drum keeps the field in, but the layout still has to keep the hot loop small.
    • Data sheet 4319.

    Sizing and Layout Notes

    Choose 33 uH when the ripple target is in the middle of the design window: the DCR stays at 53 mOhm and the saturation limit at 3.86 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Is the part shielded?
    Yes, magnetically shielded, which is what keeps the field out of the radios, sensors and ADAS front ends that share the module.

    Is the part shielded?
    Yes, magnetically shielded, which is what keeps the field out of the radios, sensors and ADAS front ends that share the module.

    Is the part shielded?
    Yes, magnetically shielded, which is what keeps the field out of the radios, sensors and ADAS front ends that share the module.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message