Eaton DRA125-331-R - 330 uH AEC-Q200 Power Inductor
Eaton DRA125-331-R - 330 uH AEC-Q200 Power Inductor

Eaton DRA125-331-R - 330 uH AEC-Q200 Power Inductor

Share
Eaton DRA125-331-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 330 uH, 1 A, DCR 543 mOhm.
    • Product Details
    • Download

    Eaton DRA125-331-R - 330 uH AEC-Q200 Power Inductor

    DRA125-331-R at a glance: shielded drum core inductor, 330 uH, 1 A Irms, 1.19 A Isat, DCR 543 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRA125-331-R
    Rated inductance330 uH ±20%
    Open circuit inductance (OCL)325 uH
    Irms (40 °C rise)1 A
    Isat1 (30% rolloff @ +25 °C)1.19 A
    Isat2 (40% rolloff @ +125 °C)0.96 A
    DCR typical @ 20 °C543 mOhm
    DCR maximum @ 20 °C650 mOhm
    K-factor (Bp-p = K x L x dI)6.4
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Under-hood and in-module electronics see temperature cycling, vibration and long service life. The DRA/DRAP/DRAQ parts are built for that: AEC-Q200, wider temperature range, and mechanical features that keep the part attached.

    At 165 °C the copper resistivity is about 60% higher than at 20 °C, so the DCR in the table is optimistic at the hot corner - budget the loss accordingly.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    DRA125 is the 12.5 mm AEC-Q200 part at mid height - more current than DRA124, same footprint, so an upgrade does not force a board respin.

    • Typical applications: Automotive DC-DC converters, body control modules, LED lighting, ADAS, infotainment supplies.
    • Shielding matters in a module full of radios and sensors: the closed drum keeps the field in, but the layout still has to keep the hot loop small.
    • Data sheet 4319.

    Design Notes

    At 330 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 543 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    How does it differ from the commercial DR part of the same size?
    The electrical shape is similar, the qualification, the temperature range and often the terminal construction are not. Do not assume drop-in equivalence.

    Is the part shielded?
    Yes, magnetically shielded, which is what keeps the field out of the radios, sensors and ADAS front ends that share the module.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message