Eaton DRA125-4R7-R Automotive Drum Core Inductor 4.7 uH
Eaton DRA125-4R7-R Automotive Drum Core Inductor 4.7 uH

Eaton DRA125-4R7-R Automotive Drum Core Inductor 4.7 uH

Share
Eaton DRA125-4R7-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 4.7 uH, 7.67 A, DCR 9.2 mOhm.
    • Product Details
    • Download

    Eaton DRA125-4R7-R Automotive Drum Core Inductor 4.7 uH

    DRA125-4R7-R at a glance: shielded drum core inductor, 4.7 uH, 7.67 A Irms, 9.76 A Isat, DCR 9.2 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRA125-4R7-R
    Rated inductance4.7 uH ±20%
    Open circuit inductance (OCL)4.9 uH
    Irms (40 °C rise)7.67 A
    Isat1 (30% rolloff @ +25 °C)9.76 A
    Isat2 (40% rolloff @ +125 °C)7.81 A
    DCR typical @ 20 °C9.2 mOhm
    DCR maximum @ 20 °C11 mOhm
    K-factor (Bp-p = K x L x dI)52
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    The Figures Explained

    Under-hood and in-module electronics see temperature cycling, vibration and long service life. The DRA/DRAP/DRAQ parts are built for that: AEC-Q200, wider temperature range, and mechanical features that keep the part attached.

    Automotive thermal cycles are the hard part: the part may be rated to 165 °C, but every power cycle flexes the solder joint. The four-terminal variants exist precisely because two terminals are not always enough.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    What This Family Is For

    DRA125 is the 12.5 mm AEC-Q200 part at mid height - more current than DRA124, same footprint, so an upgrade does not force a board respin.

    • Typical applications: Automotive DC-DC converters, body control modules, LED lighting, ADAS, infotainment supplies.
    • Shielding matters in a module full of radios and sensors: the closed drum keeps the field in, but the layout still has to keep the hot loop small.
    • Data sheet 4319.

    Design Notes

    Choose 4.7 uH when the ripple target is in the middle of the design window: the DCR stays at 9.2 mOhm and the saturation limit at 9.76 A leaves the transient room it needs.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    Is the part shielded?
    Yes, magnetically shielded, which is what keeps the field out of the radios, sensors and ADAS front ends that share the module.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products