Eaton DRA125-R47-R Automotive Shielded Inductor 33.2 A
Eaton DRA125-R47-R Automotive Shielded Inductor 33.2 A

Eaton DRA125-R47-R Automotive Shielded Inductor 33.2 A

Share
Eaton DRA125-R47-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 0.47 uH, 14.7 A, DCR 2.5 mOhm.
    • Product Details
    • Download

    Eaton DRA125-R47-R Automotive Shielded Inductor 33.2 A

    DRA125-R47-R at a glance: shielded drum core inductor, 0.47 uH, 14.7 A Irms, 33.2 A Isat, DCR 2.5 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRA125-R47-R
    Rated inductance0.47 uH ±20%
    Open circuit inductance (OCL)0.45 uH
    Irms (40 °C rise)14.7 A
    Isat1 (30% rolloff @ +25 °C)33.2 A
    Isat2 (40% rolloff @ +125 °C)26.6 A
    DCR typical @ 20 °C2.5 mOhm
    DCR maximum @ 20 °C3 mOhm
    K-factor (Bp-p = K x L x dI)177
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Under-hood and in-module electronics see temperature cycling, vibration and long service life. The DRA/DRAP/DRAQ parts are built for that: AEC-Q200, wider temperature range, and mechanical features that keep the part attached.

    The 165 °C figure is ambient plus self-temperature rise, which means the part can be genuinely hot in service. Derate the current for the real ambient, not for a 25 °C bench, and check the solder joint as well as the winding.

    Saturation degrades with temperature on ferrite. Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Positioning in the Range

    DRA125 is the 12.5 mm AEC-Q200 part at mid height - more current than DRA124, same footprint, so an upgrade does not force a board respin.

    • Typical applications: Automotive DC-DC converters, body control modules, LED lighting, ADAS, infotainment supplies.
    • Shielding matters in a module full of radios and sensors: the closed drum keeps the field in, but the layout still has to keep the hot loop small.
    • Data sheet 4319.

    Sizing It Into a Design

    Choose 0.47 uH when the ripple target is at the low end of the design window: the DCR stays at 2.5 mOhm and the saturation limit at 33.2 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    What is the operating temperature?
    -40 °C to +165 °C, ambient plus self-temperature rise. That covers under-hood modules with margin for the rise.

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products