Eaton DRA127-150-R - 15 uH AEC-Q200 Power Inductor
Eaton DRA127-150-R - 15 uH AEC-Q200 Power Inductor

Eaton DRA127-150-R - 15 uH AEC-Q200 Power Inductor

Share
Eaton DRA127-150-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 15 uH, 4.83 A, DCR 27 mOhm.
    • Product Details
    • Download

    Eaton DRA127-150-R - 15 uH AEC-Q200 Power Inductor

    DRA127-150-R at a glance: shielded drum core inductor, 15 uH, 4.83 A Irms, 9.03 A Isat, DCR 27 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRA127-150-R
    Rated inductance15 uH ±20%
    Open circuit inductance (OCL)14.9 uH
    Irms (40 °C rise)4.83 A
    Isat1 (30% rolloff @ +25 °C)9.03 A
    Isat2 (40% rolloff @ +125 °C)7.23 A
    DCR typical @ 20 °C27 mOhm
    DCR maximum @ 20 °C32 mOhm
    K-factor (Bp-p = K x L x dI)19.4
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Under-hood and in-module electronics see temperature cycling, vibration and long service life. The DRA/DRAP/DRAQ parts are built for that: AEC-Q200, wider temperature range, and mechanical features that keep the part attached.

    The 165 °C figure is ambient plus self-temperature rise, which means the part can be genuinely hot in service. Derate the current for the real ambient, not for a 25 °C bench, and check the solder joint as well as the winding.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Series Positioning

    DRA127 is the tallest and highest-current AEC-Q200 drum core in the DRA range, up to 56 A. Built for the under-hood and high-vibration end of automotive.

    • Typical applications: Automotive power conversion, body electronics, lighting, ADAS, HVAC and seat control.
    • Under-hood thermal cycling is the hard part: the part is rated to 165 °C, but the solder joints and the PCB see the same cycles.
    • Data sheet 4319.

    Design Notes

    15 uH is in the middle of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    What does AEC-Q200 cover?
    The qualification of the component itself: thermal shock, vibration, moisture, life and electrical stress. It does not qualify your assembly or your thermal design.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products