Eaton DRA127-1R5-R AEC-Q200 Shielded Inductor, 1.5 uH
Eaton DRA127-1R5-R AEC-Q200 Shielded Inductor, 1.5 uH

Eaton DRA127-1R5-R AEC-Q200 Shielded Inductor, 1.5 uH

Share
Eaton DRA127-1R5-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 1.5 uH, 12.2 A, DCR 4.3 mOhm.
    • Product Details
    • Download

    Eaton DRA127-1R5-R AEC-Q200 Shielded Inductor, 1.5 uH

    DRA127-1R5-R at a glance: shielded drum core inductor, 1.5 uH, 12.2 A Irms, 31.1 A Isat, DCR 4.3 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRA127-1R5-R
    Rated inductance1.5 uH ±20%
    Open circuit inductance (OCL)1.27 uH
    Irms (40 °C rise)12.2 A
    Isat1 (30% rolloff @ +25 °C)31.1 A
    Isat2 (40% rolloff @ +125 °C)24.9 A
    DCR typical @ 20 °C4.3 mOhm
    DCR maximum @ 20 °C5.1 mOhm
    K-factor (Bp-p = K x L x dI)66.7
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    AEC-Q200 is the entry ticket, not the destination. This part is qualified to the automotive standard and rated to 165 °C ambient plus self-heating, in a shielded drum core built to survive shock and vibration rather than a laboratory bench.

    Automotive thermal cycles are the hard part: the part may be rated to 165 °C, but every power cycle flexes the solder joint. The four-terminal variants exist precisely because two terminals are not always enough.

    Isat is a magnetic limit, not a thermal one. Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Where This Series Fits

    DRA127 is the tallest and highest-current AEC-Q200 drum core in the DRA range, up to 56 A. Built for the under-hood and high-vibration end of automotive.

    • Typical applications: Automotive power conversion, body electronics, lighting, ADAS, HVAC and seat control.
    • Under-hood thermal cycling is the hard part: the part is rated to 165 °C, but the solder joints and the PCB see the same cycles.
    • Data sheet 4319.

    Design Notes

    Choose 1.5 uH when the ripple target is in the middle of the design window: the DCR stays at 4.3 mOhm and the saturation limit at 31.1 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    How does it differ from the commercial DR part of the same size?
    The electrical shape is similar, the qualification, the temperature range and often the terminal construction are not. Do not assume drop-in equivalence.

    Is the part shielded?
    Yes, magnetically shielded, which is what keeps the field out of the radios, sensors and ADAS front ends that share the module.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products