Eaton DRA127-221-R - 220 uH AEC-Q200 Power Inductor
Eaton DRA127-221-R - 220 uH AEC-Q200 Power Inductor

Eaton DRA127-221-R - 220 uH AEC-Q200 Power Inductor

Share
Eaton DRA127-221-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 220 uH, 1.25 A, DCR 398 mOhm.
    • Product Details
    • Download

    Eaton DRA127-221-R - 220 uH AEC-Q200 Power Inductor

    DRA127-221-R at a glance: shielded drum core inductor, 220 uH, 1.25 A Irms, 2.35 A Isat, DCR 398 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRA127-221-R
    Rated inductance220 uH ±20%
    Open circuit inductance (OCL)220 uH
    Irms (40 °C rise)1.25 A
    Isat1 (30% rolloff @ +25 °C)2.35 A
    Isat2 (40% rolloff @ +125 °C)1.88 A
    DCR typical @ 20 °C398 mOhm
    DCR maximum @ 20 °C480 mOhm
    K-factor (Bp-p = K x L x dI)5
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Automotive magnetics are specified differently: the temperature range is wider, the qualification is AEC-Q200, and the construction has to hold together under vibration that would shake a commercial part off its pads. That is what the DRA series is.

    Thermal margin in a module is not the same as thermal margin on a bench. The ratings assume a mounting condition; the enclosure, the potting and the neighbouring components change it.

    Isat is a magnetic limit, not a thermal one. Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Positioning in the Range

    DRA127 is the tallest and highest-current AEC-Q200 drum core in the DRA range, up to 56 A. Built for the under-hood and high-vibration end of automotive.

    • Typical applications: Automotive power conversion, body electronics, lighting, ADAS, HVAC and seat control.
    • Under-hood thermal cycling is the hard part: the part is rated to 165 °C, but the solder joints and the PCB see the same cycles.
    • Data sheet 4319.

    Sizing and Layout Notes

    At 220 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 398 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    Is the part shielded?
    Yes, magnetically shielded, which is what keeps the field out of the radios, sensors and ADAS front ends that share the module.

    What does AEC-Q200 cover?
    The qualification of the component itself: thermal shock, vibration, moisture, life and electrical stress. It does not qualify your assembly or your thermal design.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products