Eaton DRA127-2R2-R Automotive Shielded Inductor 25.5 A
Eaton DRA127-2R2-R Automotive Shielded Inductor 25.5 A

Eaton DRA127-2R2-R Automotive Shielded Inductor 25.5 A

Share
Eaton DRA127-2R2-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 2.2 uH, 12.5 A, DCR 4 mOhm.
    • Product Details
    • Download

    Eaton DRA127-2R2-R Automotive Shielded Inductor 25.5 A

    DRA127-2R2-R at a glance: shielded drum core inductor, 2.2 uH, 12.5 A Irms, 25.5 A Isat, DCR 4 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRA127-2R2-R
    Rated inductance2.2 uH ±20%
    Open circuit inductance (OCL)1.92 uH
    Irms (40 °C rise)12.5 A
    Isat1 (30% rolloff @ +25 °C)25.5 A
    Isat2 (40% rolloff @ +125 °C)20.4 A
    DCR typical @ 20 °C4 mOhm
    DCR maximum @ 20 °C4.8 mOhm
    K-factor (Bp-p = K x L x dI)54.6
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Automotive magnetics are specified differently: the temperature range is wider, the qualification is AEC-Q200, and the construction has to hold together under vibration that would shake a commercial part off its pads. That is what the DRA series is.

    Thermal margin in a module is not the same as thermal margin on a bench. The ratings assume a mounting condition; the enclosure, the potting and the neighbouring components change it.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Where This Series Fits

    DRA127 is the tallest and highest-current AEC-Q200 drum core in the DRA range, up to 56 A. Built for the under-hood and high-vibration end of automotive.

    • Typical applications: Automotive power conversion, body electronics, lighting, ADAS, HVAC and seat control.
    • Under-hood thermal cycling is the hard part: the part is rated to 165 °C, but the solder joints and the PCB see the same cycles.
    • Data sheet 4319.

    Sizing and Layout Notes

    At 2.2 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 4 mOhm DCR - more turns, thinner wire, more resistance.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Is the part shielded?
    Yes, magnetically shielded, which is what keeps the field out of the radios, sensors and ADAS front ends that share the module.

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    What is the operating temperature?
    -40 °C to +165 °C, ambient plus self-temperature rise. That covers under-hood modules with margin for the rise.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products