Eaton DRA127-470-R - 47 uH AEC-Q200 Power Inductor
Eaton DRA127-470-R - 47 uH AEC-Q200 Power Inductor

Eaton DRA127-470-R - 47 uH AEC-Q200 Power Inductor

Share
Eaton DRA127-470-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 47 uH, 2.62 A, DCR 91 mOhm.
    • Product Details
    • Download

    Eaton DRA127-470-R - 47 uH AEC-Q200 Power Inductor

    DRA127-470-R at a glance: shielded drum core inductor, 47 uH, 2.62 A Irms, 5.09 A Isat, DCR 91 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRA127-470-R
    Rated inductance47 uH ±20%
    Open circuit inductance (OCL)47.9 uH
    Irms (40 °C rise)2.62 A
    Isat1 (30% rolloff @ +25 °C)5.09 A
    Isat2 (40% rolloff @ +125 °C)4.07 A
    DCR typical @ 20 °C91 mOhm
    DCR maximum @ 20 °C110 mOhm
    K-factor (Bp-p = K x L x dI)10.9
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Automotive magnetics are specified differently: the temperature range is wider, the qualification is AEC-Q200, and the construction has to hold together under vibration that would shake a commercial part off its pads. That is what the DRA series is.

    At 165 °C the copper resistivity is about 60% higher than at 20 °C, so the DCR in the table is optimistic at the hot corner - budget the loss accordingly.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Where This Series Fits

    DRA127 is the tallest and highest-current AEC-Q200 drum core in the DRA range, up to 56 A. Built for the under-hood and high-vibration end of automotive.

    • Typical applications: Automotive power conversion, body electronics, lighting, ADAS, HVAC and seat control.
    • Under-hood thermal cycling is the hard part: the part is rated to 165 °C, but the solder joints and the PCB see the same cycles.
    • Data sheet 4319.

    Sizing It Into a Design

    47 uH is in the middle of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    What is the operating temperature?
    -40 °C to +165 °C, ambient plus self-temperature rise. That covers under-hood modules with margin for the rise.

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products