Eaton DRA127-4R7-R 4.7 uH AEC-Q200 Drum Core, 8.14 A
Eaton DRA127-4R7-R 4.7 uH AEC-Q200 Drum Core, 8.14 A

Eaton DRA127-4R7-R 4.7 uH AEC-Q200 Drum Core, 8.14 A

Share
Eaton DRA127-4R7-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 4.7 uH, 8.14 A, DCR 9.4 mOhm.
    • Product Details
    • Download

    Eaton DRA127-4R7-R 4.7 uH AEC-Q200 Drum Core, 8.14 A

    DRA127-4R7-R at a glance: shielded drum core inductor, 4.7 uH, 8.14 A Irms, 16.5 A Isat, DCR 9.4 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRA127-4R7-R
    Rated inductance4.7 uH ±20%
    Open circuit inductance (OCL)4.58 uH
    Irms (40 °C rise)8.14 A
    Isat1 (30% rolloff @ +25 °C)16.5 A
    Isat2 (40% rolloff @ +125 °C)13.2 A
    DCR typical @ 20 °C9.4 mOhm
    DCR maximum @ 20 °C11 mOhm
    K-factor (Bp-p = K x L x dI)35.3
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    AEC-Q200 is the entry ticket, not the destination. This part is qualified to the automotive standard and rated to 165 °C ambient plus self-heating, in a shielded drum core built to survive shock and vibration rather than a laboratory bench.

    Automotive thermal cycles are the hard part: the part may be rated to 165 °C, but every power cycle flexes the solder joint. The four-terminal variants exist precisely because two terminals are not always enough.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    What This Family Is For

    DRA127 is the tallest and highest-current AEC-Q200 drum core in the DRA range, up to 56 A. Built for the under-hood and high-vibration end of automotive.

    • Typical applications: Automotive power conversion, body electronics, lighting, ADAS, HVAC and seat control.
    • Under-hood thermal cycling is the hard part: the part is rated to 165 °C, but the solder joints and the PCB see the same cycles.
    • Data sheet 4319.

    Sizing and Layout Notes

    Choose 4.7 uH when the ripple target is in the middle of the design window: the DCR stays at 9.4 mOhm and the saturation limit at 16.5 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    Is the part shielded?
    Yes, magnetically shielded, which is what keeps the field out of the radios, sensors and ADAS front ends that share the module.

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products