Eaton DRA127-821-R 820 uH AEC-Q200 Drum Core, 0.64 A
Eaton DRA127-821-R 820 uH AEC-Q200 Drum Core, 0.64 A

Eaton DRA127-821-R 820 uH AEC-Q200 Drum Core, 0.64 A

Share
Eaton DRA127-821-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 820 uH, 0.64 A, DCR 1.54 ohm.
    • Product Details
    • Download

    Eaton DRA127-821-R 820 uH AEC-Q200 Drum Core, 0.64 A

    DRA127-821-R at a glance: shielded drum core inductor, 820 uH, 0.64 A Irms, 1.22 A Isat, DCR 1540 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRA127-821-R
    Rated inductance820 uH ±20%
    Open circuit inductance (OCL)825 uH
    Irms (40 °C rise)0.64 A
    Isat1 (30% rolloff @ +25 °C)1.22 A
    Isat2 (40% rolloff @ +125 °C)0.98 A
    DCR typical @ 20 °C1540 mOhm
    DCR maximum @ 20 °C1850 mOhm
    K-factor (Bp-p = K x L x dI)2.6
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Automotive magnetics are specified differently: the temperature range is wider, the qualification is AEC-Q200, and the construction has to hold together under vibration that would shake a commercial part off its pads. That is what the DRA series is.

    At 165 °C the copper resistivity is about 60% higher than at 20 °C, so the DCR in the table is optimistic at the hot corner - budget the loss accordingly.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Where This Series Fits

    DRA127 is the tallest and highest-current AEC-Q200 drum core in the DRA range, up to 56 A. Built for the under-hood and high-vibration end of automotive.

    • Typical applications: Automotive power conversion, body electronics, lighting, ADAS, HVAC and seat control.
    • Under-hood thermal cycling is the hard part: the part is rated to 165 °C, but the solder joints and the PCB see the same cycles.
    • Data sheet 4319.

    Sizing It Into a Design

    At 820 uH this part is at the high end of the family. The winding that produces that inductance is also what sets the 1540 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    What is the operating temperature?
    -40 °C to +165 °C, ambient plus self-temperature rise. That covers under-hood modules with margin for the rise.

    How does it differ from the commercial DR part of the same size?
    The electrical shape is similar, the qualification, the temperature range and often the terminal construction are not. Do not assume drop-in equivalence.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products