Eaton DRA127-8R2-R AEC-Q200 Shielded Inductor, 8.2 uH
Eaton DRA127-8R2-R AEC-Q200 Shielded Inductor, 8.2 uH

Eaton DRA127-8R2-R AEC-Q200 Shielded Inductor, 8.2 uH

Share
Eaton DRA127-8R2-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 8.2 uH, 6.33 A, DCR 16 mOhm.
    • Product Details
    • Download

    Eaton DRA127-8R2-R AEC-Q200 Shielded Inductor, 8.2 uH

    DRA127-8R2-R at a glance: shielded drum core inductor, 8.2 uH, 6.33 A Irms, 12.2 A Isat, DCR 16 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRA127-8R2-R
    Rated inductance8.2 uH ±20%
    Open circuit inductance (OCL)8.33 uH
    Irms (40 °C rise)6.33 A
    Isat1 (30% rolloff @ +25 °C)12.2 A
    Isat2 (40% rolloff @ +125 °C)9.74 A
    DCR typical @ 20 °C16 mOhm
    DCR maximum @ 20 °C19 mOhm
    K-factor (Bp-p = K x L x dI)26.1
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    The Figures Explained

    Under-hood and in-module electronics see temperature cycling, vibration and long service life. The DRA/DRAP/DRAQ parts are built for that: AEC-Q200, wider temperature range, and mechanical features that keep the part attached.

    Automotive thermal cycles are the hard part: the part may be rated to 165 °C, but every power cycle flexes the solder joint. The four-terminal variants exist precisely because two terminals are not always enough.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Series Positioning

    DRA127 is the tallest and highest-current AEC-Q200 drum core in the DRA range, up to 56 A. Built for the under-hood and high-vibration end of automotive.

    • Typical applications: Automotive power conversion, body electronics, lighting, ADAS, HVAC and seat control.
    • Under-hood thermal cycling is the hard part: the part is rated to 165 °C, but the solder joints and the PCB see the same cycles.
    • Data sheet 4319.

    Putting It to Work

    At 8.2 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 16 mOhm DCR - more turns, thinner wire, more resistance.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    What is the operating temperature?
    -40 °C to +165 °C, ambient plus self-temperature rise. That covers under-hood modules with margin for the rise.

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message