Eaton DRA127-R47-R Automotive Drum Core Inductor 0.47 uH
Eaton DRA127-R47-R Automotive Drum Core Inductor 0.47 uH

Eaton DRA127-R47-R Automotive Drum Core Inductor 0.47 uH

Share
Eaton DRA127-R47-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 0.47 uH, 15.9 A, DCR 2.4 mOhm.
    • Product Details
    • Download

    Eaton DRA127-R47-R Automotive Drum Core Inductor 0.47 uH

    DRA127-R47-R at a glance: shielded drum core inductor, 0.47 uH, 15.9 A Irms, 56 A Isat, DCR 2.4 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRA127-R47-R
    Rated inductance0.47 uH ±20%
    Open circuit inductance (OCL)0.41 uH
    Irms (40 °C rise)15.9 A
    Isat1 (30% rolloff @ +25 °C)56 A
    Isat2 (40% rolloff @ +125 °C)44.8 A
    DCR typical @ 20 °C2.4 mOhm
    DCR maximum @ 20 °C3 mOhm
    K-factor (Bp-p = K x L x dI)120
    Package12.5 x 12.5 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    AEC-Q200 is the entry ticket, not the destination. This part is qualified to the automotive standard and rated to 165 °C ambient plus self-heating, in a shielded drum core built to survive shock and vibration rather than a laboratory bench.

    Thermal margin in a module is not the same as thermal margin on a bench. The ratings assume a mounting condition; the enclosure, the potting and the neighbouring components change it.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Series Positioning

    DRA127 is the tallest and highest-current AEC-Q200 drum core in the DRA range, up to 56 A. Built for the under-hood and high-vibration end of automotive.

    • Typical applications: Automotive power conversion, body electronics, lighting, ADAS, HVAC and seat control.
    • Under-hood thermal cycling is the hard part: the part is rated to 165 °C, but the solder joints and the PCB see the same cycles.
    • Data sheet 4319.

    Sizing It Into a Design

    0.47 uH sits at the low end of the range, and the trade at that point is explicit: 2.4 mOhm of DCR against 56 A of saturation headroom.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    What is the operating temperature?
    -40 °C to +165 °C, ambient plus self-temperature rise. That covers under-hood modules with margin for the rise.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products