Eaton DRA73-100-R - 10 uH AEC-Q200 Power Inductor
Eaton DRA73-100-R - 10 uH AEC-Q200 Power Inductor

Eaton DRA73-100-R - 10 uH AEC-Q200 Power Inductor

Share
Eaton DRA73-100-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 10 uH, 2.11 A, DCR 64 mOhm.
    • Product Details
    • Download

    Eaton DRA73-100-R - 10 uH AEC-Q200 Power Inductor

    DRA73-100-R at a glance: shielded drum core inductor, 10 uH, 2.11 A Irms, 2.39 A Isat, DCR 64 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRA73-100-R
    Rated inductance10 uH ±20%
    Open circuit inductance (OCL)10.3 uH
    Irms (40 °C rise)2.11 A
    Isat1 (30% rolloff @ +25 °C)2.39 A
    Isat2 (40% rolloff @ +125 °C)1.91 A
    DCR typical @ 20 °C64 mOhm
    DCR maximum @ 20 °C77 mOhm
    K-factor (Bp-p = K x L x dI)103
    Package7.6 x 7.6 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    This is the automotive grade version of the drum core family: AEC-Q200 qualified, shielded, and rated to 165 °C including self-temperature rise. The electrical behaviour is familiar; the qualification and the mechanical build are not.

    Automotive thermal cycles are the hard part: the part may be rated to 165 °C, but every power cycle flexes the solder joint. The four-terminal variants exist precisely because two terminals are not always enough.

    Isat is a magnetic limit, not a thermal one. Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Where This Series Fits

    DRA73 is the smallest AEC-Q200 part in the DRA range: a 7.6 x 7.6 mm shielded drum core qualified to 165 °C ambient plus self-heating, built for shock and vibration rather than for a benign bench supply.

    • Typical applications: Body electronics, LED lighting, HVAC controllers, door and seat modules, ADAS and infotainment supplies.
    • The 165 °C rating covers ambient plus self-temperature rise - the loss budget still has to close at the hot corner, not at 25 °C.
    • Data sheet 4319.

    Design Notes

    Choose 10 uH when the ripple target is in the middle of the design window: the DCR stays at 64 mOhm and the saturation limit at 2.39 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    How does it differ from the commercial DR part of the same size?
    The electrical shape is similar, the qualification, the temperature range and often the terminal construction are not. Do not assume drop-in equivalence.

    How does it differ from the commercial DR part of the same size?
    The electrical shape is similar, the qualification, the temperature range and often the terminal construction are not. Do not assume drop-in equivalence.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message