Eaton DRA73-821-R - 820 uH AEC-Q200 Power Inductor
Eaton DRA73-821-R - 820 uH AEC-Q200 Power Inductor

Eaton DRA73-821-R - 820 uH AEC-Q200 Power Inductor

Share
Eaton DRA73-821-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 820 uH, 0.25 A, DCR 4.46 ohm.
    • Product Details
    • Download

    Eaton DRA73-821-R - 820 uH AEC-Q200 Power Inductor

    DRA73-821-R at a glance: shielded drum core inductor, 820 uH, 0.25 A Irms, 0.27 A Isat, DCR 4460 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRA73-821-R
    Rated inductance820 uH ±20%
    Open circuit inductance (OCL)825 uH
    Irms (40 °C rise)0.25 A
    Isat1 (30% rolloff @ +25 °C)0.27 A
    Isat2 (40% rolloff @ +125 °C)0.21 A
    DCR typical @ 20 °C4460 mOhm
    DCR maximum @ 20 °C5350 mOhm
    K-factor (Bp-p = K x L x dI)11.5
    Package7.6 x 7.6 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Automotive magnetics are specified differently: the temperature range is wider, the qualification is AEC-Q200, and the construction has to hold together under vibration that would shake a commercial part off its pads. That is what the DRA series is.

    Automotive thermal cycles are the hard part: the part may be rated to 165 °C, but every power cycle flexes the solder joint. The four-terminal variants exist precisely because two terminals are not always enough.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Where This Series Fits

    DRA73 is the smallest AEC-Q200 part in the DRA range: a 7.6 x 7.6 mm shielded drum core qualified to 165 °C ambient plus self-heating, built for shock and vibration rather than for a benign bench supply.

    • Typical applications: Body electronics, LED lighting, HVAC controllers, door and seat modules, ADAS and infotainment supplies.
    • The 165 °C rating covers ambient plus self-temperature rise - the loss budget still has to close at the hot corner, not at 25 °C.
    • Data sheet 4319.

    Sizing and Layout Notes

    Choose 820 uH when the ripple target is at the high end of the design window: the DCR stays at 4460 mOhm and the saturation limit at 0.27 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    What is the operating temperature?
    -40 °C to +165 °C, ambient plus self-temperature rise. That covers under-hood modules with margin for the rise.

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    Is the part shielded?
    Yes, magnetically shielded, which is what keeps the field out of the radios, sensors and ADAS front ends that share the module.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message