Eaton DRA74-4R7-R AEC-Q200 Shielded Inductor, 4.7 uH
Eaton DRA74-4R7-R AEC-Q200 Shielded Inductor, 4.7 uH

Eaton DRA74-4R7-R AEC-Q200 Shielded Inductor, 4.7 uH

Share
Eaton DRA74-4R7-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 4.7 uH, 3.41 A, DCR 24 mOhm.
    • Product Details
    • Download

    Eaton DRA74-4R7-R AEC-Q200 Shielded Inductor, 4.7 uH

    DRA74-4R7-R at a glance: shielded drum core inductor, 4.7 uH, 3.41 A Irms, 4.38 A Isat, DCR 24 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRA74-4R7-R
    Rated inductance4.7 uH ±20%
    Open circuit inductance (OCL)4.68 uH
    Irms (40 °C rise)3.41 A
    Isat1 (30% rolloff @ +25 °C)4.38 A
    Isat2 (40% rolloff @ +125 °C)3.5 A
    DCR typical @ 20 °C24 mOhm
    DCR maximum @ 20 °C29 mOhm
    K-factor (Bp-p = K x L x dI)130
    Package7.6 x 7.6 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Under-hood and in-module electronics see temperature cycling, vibration and long service life. The DRA/DRAP/DRAQ parts are built for that: AEC-Q200, wider temperature range, and mechanical features that keep the part attached.

    The 165 °C figure is ambient plus self-temperature rise, which means the part can be genuinely hot in service. Derate the current for the real ambient, not for a 25 °C bench, and check the solder joint as well as the winding.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Where This Series Fits

    DRA74 shares the 7.6 mm pad with DRA73 and stands taller, which is how it reaches the higher current ratings in this size. AEC-Q200, 165 °C, shielded.

    • Typical applications: Automotive body control, LED drivers, ADAS modules, HVAC and seat controllers, infotainment.
    • Automotive derating practice usually wants margin on both Irms and Isat at the maximum ambient - do not size to the headline numbers alone.
    • Data sheet 4319.

    Sizing It Into a Design

    Choose 4.7 uH when the ripple target is in the middle of the design window: the DCR stays at 24 mOhm and the saturation limit at 4.38 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification of the component itself: thermal shock, vibration, moisture, life and electrical stress. It does not qualify your assembly or your thermal design.

    What does AEC-Q200 cover?
    The qualification of the component itself: thermal shock, vibration, moisture, life and electrical stress. It does not qualify your assembly or your thermal design.

    Can I use it in a non-automotive design?
    Yes, and people do when they need the vibration and temperature headroom. You pay for the qualification you may not need.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products