Eaton DRA74-820-R 82 uH AEC-Q200 Drum Core, 0.88 A
Eaton DRA74-820-R 82 uH AEC-Q200 Drum Core, 0.88 A

Eaton DRA74-820-R 82 uH AEC-Q200 Drum Core, 0.88 A

Share
Eaton DRA74-820-R: AEC-Q200 Automotive Shielded Drum Core Inductor, 82 uH, 0.88 A, DCR 367 mOhm.
    • Product Details
    • Download

    Eaton DRA74-820-R 82 uH AEC-Q200 Drum Core, 0.88 A

    DRA74-820-R at a glance: shielded drum core inductor, 82 uH, 0.88 A Irms, 1.03 A Isat, DCR 367 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRA74-820-R
    Rated inductance82 uH ±20%
    Open circuit inductance (OCL)81.5 uH
    Irms (40 °C rise)0.88 A
    Isat1 (30% rolloff @ +25 °C)1.03 A
    Isat2 (40% rolloff @ +125 °C)0.83 A
    DCR typical @ 20 °C367 mOhm
    DCR maximum @ 20 °C440 mOhm
    K-factor (Bp-p = K x L x dI)30.8
    Package7.6 x 7.6 mm footprint
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Under-hood and in-module electronics see temperature cycling, vibration and long service life. The DRA/DRAP/DRAQ parts are built for that: AEC-Q200, wider temperature range, and mechanical features that keep the part attached.

    Automotive thermal cycles are the hard part: the part may be rated to 165 °C, but every power cycle flexes the solder joint. The four-terminal variants exist precisely because two terminals are not always enough.

    Saturation degrades with temperature on ferrite. Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    What This Family Is For

    DRA74 shares the 7.6 mm pad with DRA73 and stands taller, which is how it reaches the higher current ratings in this size. AEC-Q200, 165 °C, shielded.

    • Typical applications: Automotive body control, LED drivers, ADAS modules, HVAC and seat controllers, infotainment.
    • Automotive derating practice usually wants margin on both Irms and Isat at the maximum ambient - do not size to the headline numbers alone.
    • Data sheet 4319.

    Sizing and Layout Notes

    Choose 82 uH when the ripple target is in the middle of the design window: the DCR stays at 367 mOhm and the saturation limit at 1.03 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification of the component itself: thermal shock, vibration, moisture, life and electrical stress. It does not qualify your assembly or your thermal design.

    Why are there two Isat values?
    The first is the 30% roll-off point at +25 °C, the second is the 40% roll-off at +125 °C. Hot ferrite saturates earlier, so the second number is the one to use at temperature.

    How does it differ from the commercial DR part of the same size?
    The electrical shape is similar, the qualification, the temperature range and often the terminal construction are not. Do not assume drop-in equivalence.

    Design note: the 165 °C rating is ambient plus self-heating. Close the loss budget at the hot corner, with the maximum DCR and the hot Isat figure.

    Mechanical Dimensions

    eaton-dra-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message