Eaton DRAQ127-220-R 1:1 Coupled Drum Core, 22 uH
Eaton DRAQ127-220-R 1:1 Coupled Drum Core, 22 uH

Eaton DRAQ127-220-R 1:1 Coupled Drum Core, 22 uH

Share
Eaton DRAQ127-220-R: AEC-Q200 Dual Winding Automotive Drum Core Inductor, 22 uH, 3.98 A, DCR 40 mOhm.
    • Product Details
    • Download

    Eaton DRAQ127-220-R 1:1 Coupled Drum Core, 22 uH

    DRAQ127-220-R at a glance: dual-winding shielded drum core, 22 uH per winding, 3.98 A, DCR 40 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRAQ127-220-R
    Rated inductance22 uH ±20%
    Open circuit inductance (OCL)22 uH
    Irms (40 °C rise)3.98 A
    Isat1 (30% rolloff @ +25 °C)7.57 A
    Isat2 (40% rolloff @ +125 °C)6.05 A
    DCR typical @ 20 °C40 mOhm
    DCR maximum @ 20 °C47 mOhm
    K-factor (Bp-p = K x L x dI)16.2
    Series connection88 uH, 1.99 A
    Parallel connection22 uH, 3.98 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 x 8.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    The Figures Explained

    The DRQ/DRAQ construction puts two windings on a shielded drum core with a defined 1:1 turns ratio. That ratio is what makes the part useful as a transformer: the two windings share flux, so the magnetising current is common and the ripple can be made to cancel.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Positioning in the Range

    DRAQ127 is the large dual-winding automotive part: 12.5 x 12.5 x 8.0 mm, AEC-Q200, 200 Vac winding isolation, and enough copper to run tens of amps in parallel mode.

    • Typical applications: Automotive DC-DC, SEPIC and flyback, body control, LED lighting, filter chokes.
    • Parallel and series ratings differ by roughly 4x in inductance - read the right column before you specify a winding connection.
    • Data sheet 4372.

    Design Notes

    22 uH sits in the middle of the range, and the trade at that point is explicit: 40 mOhm of DCR against 7.57 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Design note: parallel and series ratings differ by about 4x. Read the column that matches the connection you intend to use, and keep the winding isolation rating in mind.

    Mechanical Dimensions

    eaton-draq127-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message