Eaton DRAQ127-330-R Dual Winding Shielded Inductor, 33 uH uH
Eaton DRAQ127-330-R Dual Winding Shielded Inductor, 33 uH uH

Eaton DRAQ127-330-R Dual Winding Shielded Inductor, 33 uH uH

Share
Eaton DRAQ127-330-R: AEC-Q200 Dual Winding Automotive Drum Core Inductor, 33 uH, 3.22 A, DCR 60 mOhm.
    • Product Details
    • Download

    Eaton DRAQ127-330-R Dual Winding Shielded Inductor, 33 uH uH

    DRAQ127-330-R at a glance: dual-winding shielded drum core, 33 uH per winding, 3.22 A, DCR 60 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRAQ127-330-R
    Rated inductance33 uH ±20%
    Open circuit inductance (OCL)32 uH
    Irms (40 °C rise)3.22 A
    Isat1 (30% rolloff @ +25 °C)6.22 A
    Isat2 (40% rolloff @ +125 °C)4.98 A
    DCR typical @ 20 °C60 mOhm
    DCR maximum @ 20 °C72 mOhm
    K-factor (Bp-p = K x L x dI)13.3
    Series connection128 uH, 1.61 A
    Parallel connection33 uH, 3.22 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 x 8.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    The DRQ/DRAQ construction puts two windings on a shielded drum core with a defined 1:1 turns ratio. That ratio is what makes the part useful as a transformer: the two windings share flux, so the magnetising current is common and the ripple can be made to cancel.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    What This Family Is For

    DRAQ127 is the large dual-winding automotive part: 12.5 x 12.5 x 8.0 mm, AEC-Q200, 200 Vac winding isolation, and enough copper to run tens of amps in parallel mode.

    • Typical applications: Automotive DC-DC, SEPIC and flyback, body control, LED lighting, filter chokes.
    • Parallel and series ratings differ by roughly 4x in inductance - read the right column before you specify a winding connection.
    • Data sheet 4372.

    Design Notes

    At 33 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 60 mOhm DCR - more turns, thinner wire, more resistance.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    Design note: parallel and series ratings differ by about 4x. Read the column that matches the connection you intend to use, and keep the winding isolation rating in mind.

    Mechanical Dimensions

    eaton-draq127-automotive-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products