Eaton DRAQ75-150-R 1:1 Coupled Drum Core, 15 uH
Eaton DRAQ75-150-R 1:1 Coupled Drum Core, 15 uH

Eaton DRAQ75-150-R 1:1 Coupled Drum Core, 15 uH

Share
Eaton DRAQ75-150-R: AEC-Q200 Dual Winding Automotive Drum Core Inductor, 15 uH, 2.8 A, DCR 80 mOhm.
    • Product Details
    • Download

    Eaton DRAQ75-150-R 1:1 Coupled Drum Core, 15 uH

    DRAQ75-150-R at a glance: dual-winding shielded drum core, 15 uH per winding, 2.8 A, DCR 80 mOhm max.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRAQ75-150-R
    Rated inductance15 uH ±20%
    Open circuit inductance (OCL)15.1 uH
    Irms (40 °C rise)2.8 A
    Isat1 (30% rolloff @ +25 °C)2.36 A
    Isat2 (40% rolloff @ +125 °C)1.89 A
    DCR maximum @ 20 °C80 mOhm
    K-factor (Bp-p = K x L x dI)67.5
    Series connection60.6 uH, 1.4 A
    Parallel connection15 uH, 2.8 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    The Figures Explained

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Saturation degrades with temperature on ferrite. Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    What This Family Is For

    DRAQ75 is an AEC-Q200 dual-winding drum core in a 7.6 x 7.6 x 4.5 mm body, with 500 Vdc isolation between windings. Parallel for current, series for inductance, coupled for a 1:1 transformer in a SEPIC or flyback.

    • Typical applications: Automotive LED drivers, body control modules, SEPIC and flyback converters, filter chokes.
    • 500 Vdc winding isolation is the highest in this group - it is still a functional rating, not reinforced insulation for a mains barrier.
    • Data sheet 11017.

    Sizing and Layout Notes

    15 uH sits in the middle of the range, and the trade at that point is explicit: - mOhm of DCR against 2.36 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Design note: parallel and series ratings differ by about 4x. Read the column that matches the connection you intend to use, and keep the winding isolation rating in mind.

    Mechanical Dimensions

    eaton-draq75-automotive-shieleded-drum-core-power-inductor-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products