Eaton DRAQ75-330-R 1:1 Coupled Drum Core, 33 uH
Eaton DRAQ75-330-R 1:1 Coupled Drum Core, 33 uH

Eaton DRAQ75-330-R 1:1 Coupled Drum Core, 33 uH

Share
Eaton DRAQ75-330-R: AEC-Q200 Dual Winding Automotive Drum Core Inductor, 33 uH, 20 A, DCR 50 ohm.
    • Product Details
    • Download

    Eaton DRAQ75-330-R 1:1 Coupled Drum Core, 33 uH

    DRAQ75-330-R at a glance: dual-winding shielded drum core, 33 uH per winding, 20 A, DCR 50000 mOhm max.

    Specification Table

    ParameterValue
    Orderable part numberDRAQ75-330-R
    Rated inductance33 uH ±20%
    Open circuit inductance (OCL)10 uH
    Irms (40 °C rise)20 A
    Isat1 (30% rolloff @ +25 °C)30 A
    Isat2 (40% rolloff @ +125 °C)40 A
    DCR maximum @ 20 °C50000 mOhm
    K-factor (Bp-p = K x L x dI)60
    Series connection70 uH, 0 A
    Parallel connection33 uH, 20 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    The Figures Explained

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    Series mode is often mistaken for a way to get more current. It is the opposite - four times the inductance, half the saturation current, twice the DCR. Use it when you need inductance, not when you need amps.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Positioning in the Range

    DRAQ75 is an AEC-Q200 dual-winding drum core in a 7.6 x 7.6 x 4.5 mm body, with 500 Vdc isolation between windings. Parallel for current, series for inductance, coupled for a 1:1 transformer in a SEPIC or flyback.

    • Typical applications: Automotive LED drivers, body control modules, SEPIC and flyback converters, filter chokes.
    • 500 Vdc winding isolation is the highest in this group - it is still a functional rating, not reinforced insulation for a mains barrier.
    • Data sheet 11017.

    Sizing It Into a Design

    At 33 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the - mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Design note: parallel and series ratings differ by about 4x. Read the column that matches the connection you intend to use, and keep the winding isolation rating in mind.

    Mechanical Dimensions

    eaton-draq75-automotive-shieleded-drum-core-power-inductor-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message