Eaton DRAQ75-4R5-R 4.5 uH Coupled Drum Core Inductor
Eaton DRAQ75-4R5-R 4.5 uH Coupled Drum Core Inductor

Eaton DRAQ75-4R5-R 4.5 uH Coupled Drum Core Inductor

Share
Eaton DRAQ75-4R5-R: AEC-Q200 Dual Winding Automotive Drum Core Inductor, 4.5 uH, 4.53 A, DCR 31 mOhm.
    • Product Details
    • Download

    Eaton DRAQ75-4R5-R 4.5 uH Coupled Drum Core Inductor

    DRAQ75-4R5-R at a glance: dual-winding shielded drum core, 4.5 uH per winding, 4.53 A, DCR 31 mOhm max.

    Specification Table

    ParameterValue
    Orderable part numberDRAQ75-4R5-R
    Rated inductance4.5 uH ±20%
    Open circuit inductance (OCL)4.48 uH
    Irms (40 °C rise)4.53 A
    Isat1 (30% rolloff @ +25 °C)4.38 A
    Isat2 (40% rolloff @ +125 °C)3.5 A
    DCR maximum @ 20 °C31 mOhm
    K-factor (Bp-p = K x L x dI)125
    Series connection17.9 uH, 2.26 A
    Parallel connection4.5 uH, 4.53 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    Coupled operation is where the part earns its keep: with the right duty cycle the two windings cancel part of the ripple, so the output capacitor sees less AC current and the converter can run at a lower switching frequency for the same ripple.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    DRAQ75 is an AEC-Q200 dual-winding drum core in a 7.6 x 7.6 x 4.5 mm body, with 500 Vdc isolation between windings. Parallel for current, series for inductance, coupled for a 1:1 transformer in a SEPIC or flyback.

    • Typical applications: Automotive LED drivers, body control modules, SEPIC and flyback converters, filter chokes.
    • 500 Vdc winding isolation is the highest in this group - it is still a functional rating, not reinforced insulation for a mains barrier.
    • Data sheet 11017.

    Sizing It Into a Design

    At 4.5 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the - mOhm DCR - more turns, thinner wire, more resistance.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Design note: parallel and series ratings differ by about 4x. Read the column that matches the connection you intend to use, and keep the winding isolation rating in mind.

    Mechanical Dimensions

    eaton-draq75-automotive-shieleded-drum-core-power-inductor-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products