Eaton DRAQ75-570-R - Dual Winding 57 uH Power Inductor
Eaton DRAQ75-570-R - Dual Winding 57 uH Power Inductor

Eaton DRAQ75-570-R - Dual Winding 57 uH Power Inductor

Share
Eaton DRAQ75-570-R: AEC-Q200 Dual Winding Automotive Drum Core Inductor, 57 uH, 20 A, DCR 50 ohm.
    • Product Details
    • Download

    Eaton DRAQ75-570-R - Dual Winding 57 uH Power Inductor

    DRAQ75-570-R at a glance: dual-winding shielded drum core, 57 uH per winding, 20 A, DCR 50000 mOhm max.

    Specification Table

    ParameterValue
    Orderable part numberDRAQ75-570-R
    Rated inductance57 uH ±20%
    Open circuit inductance (OCL)10 uH
    Irms (40 °C rise)20 A
    Isat1 (30% rolloff @ +25 °C)30 A
    Isat2 (40% rolloff @ +125 °C)40 A
    DCR maximum @ 20 °C50000 mOhm
    K-factor (Bp-p = K x L x dI)60
    Series connection70 uH, 0 A
    Parallel connection57 uH, 20 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    The Figures Explained

    The DRQ/DRAQ construction puts two windings on a shielded drum core with a defined 1:1 turns ratio. That ratio is what makes the part useful as a transformer: the two windings share flux, so the magnetising current is common and the ripple can be made to cancel.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Series Positioning

    DRAQ75 is an AEC-Q200 dual-winding drum core in a 7.6 x 7.6 x 4.5 mm body, with 500 Vdc isolation between windings. Parallel for current, series for inductance, coupled for a 1:1 transformer in a SEPIC or flyback.

    • Typical applications: Automotive LED drivers, body control modules, SEPIC and flyback converters, filter chokes.
    • 500 Vdc winding isolation is the highest in this group - it is still a functional rating, not reinforced insulation for a mains barrier.
    • Data sheet 11017.

    Sizing and Layout Notes

    57 uH sits in the middle of the range, and the trade at that point is explicit: - mOhm of DCR against 30 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Design note: parallel and series ratings differ by about 4x. Read the column that matches the connection you intend to use, and keep the winding isolation rating in mind.

    Mechanical Dimensions

    eaton-draq75-automotive-shieleded-drum-core-power-inductor-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products