Eaton DRAQ75-810-R Dual Winding Shielded Inductor, 81 uH uH
Eaton DRAQ75-810-R Dual Winding Shielded Inductor, 81 uH uH

Eaton DRAQ75-810-R Dual Winding Shielded Inductor, 81 uH uH

Share
Eaton DRAQ75-810-R: AEC-Q200 Dual Winding Automotive Drum Core Inductor, 81 uH, 1.2 A, DCR 431 mOhm.
    • Product Details
    • Download

    Eaton DRAQ75-810-R Dual Winding Shielded Inductor, 81 uH uH

    DRAQ75-810-R at a glance: dual-winding shielded drum core, 81 uH per winding, 1.2 A, DCR 431 mOhm max.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRAQ75-810-R
    Rated inductance81 uH ±20%
    Open circuit inductance (OCL)80.9 uH
    Irms (40 °C rise)1.2 A
    Isat1 (30% rolloff @ +25 °C)1.01 A
    Isat2 (40% rolloff @ +125 °C)0.81 A
    DCR maximum @ 20 °C431 mOhm
    K-factor (Bp-p = K x L x dI)28.9
    Series connection324 uH, 0.6 A
    Parallel connection81 uH, 1.2 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +165 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    The Figures Explained

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    Isat1 is the 30% rolloff point at +25 °C, Isat2 the 40% rolloff at +125 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Where This Series Fits

    DRAQ75 is an AEC-Q200 dual-winding drum core in a 7.6 x 7.6 x 4.5 mm body, with 500 Vdc isolation between windings. Parallel for current, series for inductance, coupled for a 1:1 transformer in a SEPIC or flyback.

    • Typical applications: Automotive LED drivers, body control modules, SEPIC and flyback converters, filter chokes.
    • 500 Vdc winding isolation is the highest in this group - it is still a functional rating, not reinforced insulation for a mains barrier.
    • Data sheet 11017.

    Design Notes

    81 uH sits in the middle of the range, and the trade at that point is explicit: - mOhm of DCR against 1.01 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Design note: parallel and series ratings differ by about 4x. Read the column that matches the connection you intend to use, and keep the winding isolation rating in mind.

    Mechanical Dimensions

    eaton-draq75-automotive-shieleded-drum-core-power-inductor-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products