Eaton DRQ125-100-R - Dual Winding 10 uH Power Inductor
Eaton DRQ125-100-R - Dual Winding 10 uH Power Inductor

Eaton DRQ125-100-R - Dual Winding 10 uH Power Inductor

Share
Eaton DRQ125-100-R: Dual Winding Shielded Drum Core Inductor, 10 uH, 5.35 A, DCR 18.9 mOhm.
    • Product Details
    • Download

    Eaton DRQ125-100-R - Dual Winding 10 uH Power Inductor

    DRQ125-100-R at a glance: dual-winding shielded drum core, 10 uH per winding, 5.35 A, DCR 18.9 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRQ125-100-R
    Rated inductance10 uH ±20%
    Open circuit inductance (OCL)9.65 uH
    Irms (40 °C rise)5.35 A
    Isat7.17 A
    DCR typical @ 20 °C18.9 mOhm
    Volt-microsecond rating14.6 V-us
    Series connection38.6 uH, 2.67 A
    Parallel connection10 uH, 5.35 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    A dual-winding drum core is a single core with two identical windings. Left uncoupled it is two chokes in one package; coupled, it becomes a 1:1 transformer for a SEPIC or a flyback, or a ripple-cancelling element in a multiphase converter.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    DRQ125 is the 12.5 mm dual-winding part at 6.0 mm height. Wire the windings in parallel for a high-current single inductor, in series for a high-inductance choke, or leave them coupled as a 1:1 transformer for a SEPIC or flyback.

    • Typical applications: Desktop and server power, DC-DC converters, SEPIC/flyback transformer use, LCD panels, filter chokes.
    • Coupling changes the ripple: a coupled inductor in a multi-phase converter can cancel ripple, but only if the phases are driven with the right duty cycle.
    • Data sheet DS4311.

    Sizing It Into a Design

    10 uH sits in the middle of the range, and the trade at that point is explicit: 18.9 mOhm of DCR against 7.17 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products