Eaton DRQ125-101-R Shielded Coupled Inductor 100 uH 1.78 A
Eaton DRQ125-101-R Shielded Coupled Inductor 100 uH 1.78 A

Eaton DRQ125-101-R Shielded Coupled Inductor 100 uH 1.78 A

Share
Eaton DRQ125-101-R: Dual Winding Shielded Drum Core Inductor, 100 uH, 1.78 A, DCR 170 mOhm.
    • Product Details
    • Download

    Eaton DRQ125-101-R Shielded Coupled Inductor 100 uH 1.78 A

    DRQ125-101-R at a glance: dual-winding shielded drum core, 100 uH per winding, 1.78 A, DCR 170 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRQ125-101-R
    Rated inductance100 uH ±20%
    Open circuit inductance (OCL)103 uH
    Irms (40 °C rise)1.78 A
    Isat2.2 A
    DCR typical @ 20 °C170 mOhm
    Volt-microsecond rating47.5 V-us
    Series connection411 uH, 0.89 A
    Parallel connection100 uH, 1.78 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    Coupled operation is where the part earns its keep: with the right duty cycle the two windings cancel part of the ripple, so the output capacitor sees less AC current and the converter can run at a lower switching frequency for the same ripple.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Series Positioning

    DRQ125 is the 12.5 mm dual-winding part at 6.0 mm height. Wire the windings in parallel for a high-current single inductor, in series for a high-inductance choke, or leave them coupled as a 1:1 transformer for a SEPIC or flyback.

    • Typical applications: Desktop and server power, DC-DC converters, SEPIC/flyback transformer use, LCD panels, filter chokes.
    • Coupling changes the ripple: a coupled inductor in a multi-phase converter can cancel ripple, but only if the phases are driven with the right duty cycle.
    • Data sheet DS4311.

    Sizing It Into a Design

    100 uH sits in the middle of the range, and the trade at that point is explicit: 170 mOhm of DCR against 2.2 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products