Eaton DRQ125-102-R 1:1 Coupled Drum Core, 1000 uH
Eaton DRQ125-102-R 1:1 Coupled Drum Core, 1000 uH

Eaton DRQ125-102-R 1:1 Coupled Drum Core, 1000 uH

Share
Eaton DRQ125-102-R: Dual Winding Shielded Drum Core Inductor, 1000 uH, 0.57 A, DCR 1.69 ohm.
    • Product Details
    • Download

    Eaton DRQ125-102-R 1:1 Coupled Drum Core, 1000 uH

    DRQ125-102-R at a glance: dual-winding shielded drum core, 1000 uH per winding, 0.57 A, DCR 1690 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRQ125-102-R
    Rated inductance1000 uH ±20%
    Open circuit inductance (OCL)1008 uH
    Irms (40 °C rise)0.57 A
    Isat0.7 A
    DCR typical @ 20 °C1690 mOhm
    Volt-microsecond rating149 V-us
    Series connection4032 uH, 0.28 A
    Parallel connection1000 uH, 0.57 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    Series mode is often mistaken for a way to get more current. It is the opposite - four times the inductance, half the saturation current, twice the DCR. Use it when you need inductance, not when you need amps.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Where This Series Fits

    DRQ125 is the 12.5 mm dual-winding part at 6.0 mm height. Wire the windings in parallel for a high-current single inductor, in series for a high-inductance choke, or leave them coupled as a 1:1 transformer for a SEPIC or flyback.

    • Typical applications: Desktop and server power, DC-DC converters, SEPIC/flyback transformer use, LCD panels, filter chokes.
    • Coupling changes the ripple: a coupled inductor in a multi-phase converter can cancel ripple, but only if the phases are driven with the right duty cycle.
    • Data sheet DS4311.

    Design Notes

    1000 uH sits in the middle of the range, and the trade at that point is explicit: 1690 mOhm of DCR against 0.7 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products