Eaton DRQ125-150-R Dual Winding Shielded Inductor, 15 uH uH
Eaton DRQ125-150-R Dual Winding Shielded Inductor, 15 uH uH

Eaton DRQ125-150-R Dual Winding Shielded Inductor, 15 uH uH

Share
Eaton DRQ125-150-R: Dual Winding Shielded Drum Core Inductor, 15 uH, 4.27 A, DCR 29.8 mOhm.
    • Product Details
    • Download

    Eaton DRQ125-150-R Dual Winding Shielded Inductor, 15 uH uH

    DRQ125-150-R at a glance: dual-winding shielded drum core, 15 uH per winding, 4.27 A, DCR 29.8 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRQ125-150-R
    Rated inductance15 uH ±20%
    Open circuit inductance (OCL)15.3 uH
    Irms (40 °C rise)4.27 A
    Isat5.69 A
    DCR typical @ 20 °C29.8 mOhm
    Volt-microsecond rating18.4 V-us
    Series connection61.4 uH, 2.13 A
    Parallel connection15 uH, 4.27 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    DRQ125 is the 12.5 mm dual-winding part at 6.0 mm height. Wire the windings in parallel for a high-current single inductor, in series for a high-inductance choke, or leave them coupled as a 1:1 transformer for a SEPIC or flyback.

    • Typical applications: Desktop and server power, DC-DC converters, SEPIC/flyback transformer use, LCD panels, filter chokes.
    • Coupling changes the ripple: a coupled inductor in a multi-phase converter can cancel ripple, but only if the phases are driven with the right duty cycle.
    • Data sheet DS4311.

    Sizing and Layout Notes

    At 15 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 29.8 mOhm DCR - more turns, thinner wire, more resistance.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products