Eaton DRQ125-2R2-R 2.2 uH Coupled Drum Core Inductor
Eaton DRQ125-2R2-R 2.2 uH Coupled Drum Core Inductor

Eaton DRQ125-2R2-R 2.2 uH Coupled Drum Core Inductor

Share
Eaton DRQ125-2R2-R: Dual Winding Shielded Drum Core Inductor, 2.2 uH, 10.9 A, DCR 4.5 mOhm.
    • Product Details
    • Download

    Eaton DRQ125-2R2-R 2.2 uH Coupled Drum Core Inductor

    DRQ125-2R2-R at a glance: dual-winding shielded drum core, 2.2 uH per winding, 10.9 A, DCR 4.5 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRQ125-2R2-R
    Rated inductance2.2 uH ±20%
    Open circuit inductance (OCL)2.21 uH
    Irms (40 °C rise)10.9 A
    Isat15 A
    DCR typical @ 20 °C4.5 mOhm
    Volt-microsecond rating6.97 V-us
    Series connection8.83 uH, 5.46 A
    Parallel connection2.2 uH, 10.9 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    DRQ125 is the 12.5 mm dual-winding part at 6.0 mm height. Wire the windings in parallel for a high-current single inductor, in series for a high-inductance choke, or leave them coupled as a 1:1 transformer for a SEPIC or flyback.

    • Typical applications: Desktop and server power, DC-DC converters, SEPIC/flyback transformer use, LCD panels, filter chokes.
    • Coupling changes the ripple: a coupled inductor in a multi-phase converter can cancel ripple, but only if the phases are driven with the right duty cycle.
    • Data sheet DS4311.

    Putting It to Work

    Choose 2.2 uH when the ripple target is in the middle of the design window: the DCR stays at 4.5 mOhm and the saturation limit at 15 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products