Eaton DRQ125-4R7-R - Dual Winding 4.7 uH Power Inductor
Eaton DRQ125-4R7-R - Dual Winding 4.7 uH Power Inductor

Eaton DRQ125-4R7-R - Dual Winding 4.7 uH Power Inductor

Share
Eaton DRQ125-4R7-R: Dual Winding Shielded Drum Core Inductor, 4.7 uH, 7.18 A, DCR 10.5 mOhm.
    • Product Details
    • Download

    Eaton DRQ125-4R7-R - Dual Winding 4.7 uH Power Inductor

    DRQ125-4R7-R at a glance: dual-winding shielded drum core, 4.7 uH per winding, 7.18 A, DCR 10.5 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRQ125-4R7-R
    Rated inductance4.7 uH ±20%
    Open circuit inductance (OCL)5.27 uH
    Irms (40 °C rise)7.18 A
    Isat9.71 A
    DCR typical @ 20 °C10.5 mOhm
    Volt-microsecond rating10.8 V-us
    Series connection21.1 uH, 3.59 A
    Parallel connection4.7 uH, 7.18 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    The DRQ/DRAQ construction puts two windings on a shielded drum core with a defined 1:1 turns ratio. That ratio is what makes the part useful as a transformer: the two windings share flux, so the magnetising current is common and the ripple can be made to cancel.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Series Positioning

    DRQ125 is the 12.5 mm dual-winding part at 6.0 mm height. Wire the windings in parallel for a high-current single inductor, in series for a high-inductance choke, or leave them coupled as a 1:1 transformer for a SEPIC or flyback.

    • Typical applications: Desktop and server power, DC-DC converters, SEPIC/flyback transformer use, LCD panels, filter chokes.
    • Coupling changes the ripple: a coupled inductor in a multi-phase converter can cancel ripple, but only if the phases are driven with the right duty cycle.
    • Data sheet DS4311.

    Design Notes

    4.7 uH sits in the middle of the range, and the trade at that point is explicit: 10.5 mOhm of DCR against 9.71 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products